Heavy-load grating guide
Heavy Duty FRP Grating: What It Is & How to Choose
Heavy duty is a project duty, not a universal thickness. Start with the wheel, equipment, impact or sustained load; draw how it reaches the supports; then match a molded or pultruded configuration to evidence for the same span and deflection limit.
Prepared by
Dengtai Industry
Published
·
Reviewed
An industrial access walkway from our image library. The application also depends on supports, guardrails and project approval beyond our grating supply.
Key terms
What Makes FRP Grating Heavy Duty?
The word must be tied to a defined load, support condition, deflection limit and technical evidence.
- Heavy duty FRP grating
- A fiberglass-reinforced grating configuration selected for a demanding load, traffic or service condition. The term describes the project duty; it does not identify the panel depth, bar section, support span, resin, surface or evidence by itself.
- Heavy-duty molded grating
- A molded grating configuration intended for a heavier duty than a standard pedestrian row. A high-load candidate may use greater depth, a different bar and mesh geometry or a different construction; its performance must be matched to the exact support and load case.
- Heavy-duty pultruded grating
- A pultruded panel made from directionally stronger bearing bars and cross rods for a demanding span or load. The I, T or WT section, bar direction and support arrangement are part of the structural definition.
- Uniform load
- A load distributed over an area and expressed, for example, in kPa or kN/m². It does not automatically represent a wheel, equipment foot or dropped-object load.
- Wheel or point load
- A concentrated action with a force and contact area. A forklift requires individual wheel or axle loads, tyre contact, position, movement, turning, braking and impact assumptions rather than a generic vehicle label.
- Recommended load and ultimate capacity
- A recommended or design load is the working value used under stated conditions. An ultimate or failure result is not an allowable working load. The two should never be interchanged.
- Deflection limit
- The permitted movement under a stated load. It may come from worker comfort, equipment tolerance, drainage, level changes or a project structural limit. The source and basis belong in the brief.
- Dynamic and sustained effects
- Moving, braking or impacting loads can produce responses larger than a static table. Long-term loads and elevated temperatures can add deflection through creep. Static ambient rows do not automatically close either case.
- Supply boundary
- The written division between our grating panels, fabrication and clips and the project’s support structure, guardrails, structural calculations, installation and system approval.
Load-case check
Six Load Cases Behind a Heavy-Duty Decision
Separate the ways load reaches the panel before comparing molded, pultruded or material alternatives.
Separate every load case
Do not combine pedestrian traffic, equipment feet, wheel loads and stored materials into one vague “heavy duty” description.
Draw where the load crosses the panel
A wheel between bars, beside an opening or across a joint creates a different local condition from a load centred over a support.
Match the support and clear span
The same panel can behave differently on two edges, four edges, multiple spans or a changed frame.
Demand the matching evidence
The configuration, support condition, load pattern, deflection basis and document scope must describe the product being quoted.
Project inputs
Heavy Duty FRP Grating Requirements and Evidence
Each link in the decision must describe the same panel and the same support system.
Swipe horizontally to view all columns.
| Decision | Ask first | Evidence that closes the choice |
|---|---|---|
| Is this genuinely heavy duty? | What vehicle, equipment, impact or sustained load defines the duty? | A load schedule with values, units, contact areas, position and frequency. |
| Which construction? | Does the frame create a two-way grid layout or one dominant bearing direction? | A support drawing with bearing edges, bar direction and clear span. |
| Is the section sufficient? | What depth or bar section, pitch and resin are proposed? | Load and deflection data for the same configuration and support condition. |
| Can the frame carry the panel reactions? | What is the support beam, bearing seat, fixing and available structural depth? | Structural drawing or calculation from the responsible project engineer. |
| Are openings safe? | Which bars or load paths are removed, and how are the remaining edges supported? | Opening layout, perimeter support, edge treatment and removable-piece details. |
| Is the environmental claim relevant? | What chemical, temperature, fire, UV or static-control requirement applies? | Product-specific grade, surface and test or document scope. |
Construction choice
Molded High-Load vs Pultruded Heavy-Duty Grating
The load direction and support layout decide which family deserves detailed comparison.
Swipe horizontally to view all columns.
| Decision point | Molded high-load direction | Pultruded heavy-duty direction |
|---|---|---|
| Structural grid | An integral grid can distribute load in two directions across a framed area. | Parallel bearing bars provide the main directional load path, connected by cross rods. |
| Support layout | Often reviewed where the frame supports several edges or the cut layout changes direction. | Both ends of the bearing bars must reach suitable supports. |
| Clear span | A deeper molded candidate may be considered, but the exact mesh and support condition need matching data. | Taller pultruded sections can offer directional depth, subject to the actual section and evidence. |
| Wheel and local load | Contact position between bars, mesh geometry and impact tolerance require review. | Wheel load position relative to bars, cross rods, supports and joints requires review. |
| Openings | Openings interrupt the grid and remove load paths even when the surrounding panel remains connected. | A cut bearing bar interrupts the main span and needs a deliberate end-support or transfer detail. |
| Fabrication | Full molded panels may be cut to finished layouts; handling mass rises with depth. | Panels are made to project width and bearing-bar length with piece-specific orientation. |
| Evidence trap | “High load” or a deeper mold is not a rating for every frame, cutout and load. | “Pultruded” or a taller bar is not automatically a heavy-duty rating. |
Suitability check
When Heavy Duty FRP Grating Is the Right Starting Point
Use these checks to separate a real heavy-load panel review from a label or an unsupported vehicle claim.
Specify this if…
- The actual duty can be described through wheel, axle, equipment-foot, line, impact or sustained loads.
- A support drawing identifies bearing faces, supported edges, clear spans, joints and openings.
- The project can state a deflection limit and whether the load is static, moving, repeated or long-term.
- The team can review a molded and pultruded option against the same drawing rather than choose from a product name.
- Technical data, calculation or testing can be matched to the exact panel configuration and working conditions.
Look elsewhere if…
- The buyer has only a vehicle weight and no wheel or axle load, contact area or route.
- “H20,” “forklift-rated” or “heavy-duty” is treated as a transferable product label without an exact configuration and evidence scope.
- No one can identify the support layout or who is responsible for the frame, guardrails and structural approval.
- The load is dominated by high temperature, severe impact, structural fire integrity or a shallow-depth constraint better served by steel or another engineered system.
- A standard pedestrian panel is being extended into vehicle duty purely because it is thicker or has a grit surface.
Current supply directions
Heavy Duty FRP Grating Configurations to Review
These factory configurations are candidates; none is a universal heavy-duty or vehicle rating.
Request a Project Quote| Specification | Value |
|---|---|
| Molded high-load candidate | 50 mm · 25 × 50 mm mesh · 45 kg/m² A current factory configuration listed for heavy-duty review, not a universal load rating. Support, span, load and deflection evidence must match. |
| Heavy molded candidate | 63 mm · 38 × 38 mm mesh · 52.5 kg/m² A deeper current product direction. Its mass is a handling reference and the project duty still needs matched evidence. |
| Pultruded range | Published series from 25.4 mm to 50.8 mm bar height I, T and WT sections have different geometry. The actual section, pitch, bearing direction and support condition must match the project evidence. |
| Panel layout | Full panel or factory-cut pieces Openings, edge sealing, piece marks and bar direction are fixed on the approved drawing. |
| Load evidence | Configuration-specific data required Recommended load, ultimate capacity, span definition, support arrangement, dynamic assumption and deflection basis must be identifiable. |
| Supply boundary | Grating, fabrication and agreed clips Supports, guardrails, structural approval, installation and complete access-system certification remain separate unless expressly quoted. |
Material and service
Heavy Duty FRP Grating Resin and Surface Requirements
Structural capacity, chemical resistance, fire behavior and surface performance are separate decisions.
Swipe horizontally to view all columns.
| Service condition | Usual material direction | What the technical review must add |
|---|---|---|
| Ordinary heavy-load access area | Isophthalic polyester may be the economical material direction in a suitable ordinary environment. | Exact grade, panel structure, support and load evidence. A stronger geometry does not make an ordinary resin chemically suitable. |
| Wet, chemical, wastewater or marine | Vinyl ester is commonly reviewed where stronger corrosion resistance is needed. | Chemical names, concentration, temperature, contact type, cleaning and finished-product evidence. |
| Fire or smoke requirement | Phenolic and other fire-performance directions may be reviewed against the specified requirement. | Standard, edition, specimen, construction, result and acceptance threshold. A heavy-duty claim is not a fire class. |
| Severe impact or damaged-bar consequence | Molded or pultruded geometry may respond differently, and another material may be preferable. | Expected impact energy, object, contact area, repeated damage, inspection interval and consequence of failure. |
| Electrical or anti-static requirement | Ordinary FRP is generally non-conductive; a conductive or anti-static product is a separate specification. | Resistance target, test method, earthing, accessories and system responsibility. |
| Hot service or permanent load | Temperature-resistant resin alone does not solve creep or long-term deflection. | Normal and peak temperature, duration, load location, long-term evidence and inspection allowance. |
Heavy-load applications
Where Heavy Duty FRP Grating Needs Extra Review
Loading docks, equipment areas, vehicle routes and corrosive access zones add different constraints.
Loading dock and yard drain cover
Vehicle traffic turns vehicle weight into individual wheel loads with braking, turning and impact effects. The cover, frame and supports must be reviewed together.
Wheel loads + frame + removal
Equipment access platform
Pump feet, valves, maintenance tools and removable sections create local loads that a uniform pedestrian value does not capture.
Equipment feet + service access
Industrial route and assembly area
Trolleys, wheeled equipment and temporary storage add moving and local loads. Mark the route and define what crosses each panel joint.
Route + moving loads + joints
Wastewater and chemical access
A demanding load may also involve wet, chemical or fire requirements. Each material requirement needs its own evidence.
Load + medium + cleaning
Heavy Duty Is a Load Condition
Heavy duty FRP grating is a grating configuration selected for a demanding access, traffic or structural duty. That duty may arrive as a concentrated equipment foot, a forklift wheel, a truck axle, a dropped tool, a repeated rolling route or a permanent stored load. The phrase heavy duty does not identify a universal material thickness, bar section or test class.
A 50 mm molded panel, a 63 mm molded panel and a 50 mm pultruded bearing bar are different structures. Their names do not establish the same capacity. Likewise, an H20 reference in a catalog does not prove that every panel from that supplier is approved for a road vehicle on every frame.
This guide therefore starts with four linked records:
- the actual grating configuration;
- the support layout and clear span;
- the load cases, including movement, impact and duration;
- the evidence and documents covering that exact combination.
If one record is missing, the responsible answer is to identify the gap. It is not to substitute “heavy duty,” a thicker panel or a competitor’s load class.
Why Heavy Duty FRP Grating Is Considered
FRP remains attractive in heavy-load areas when corrosion resistance, lower handling weight, drainage or electrical non-conductivity also matter. A lighter panel can be easier to lift into a pump platform, dock or treatment area. An open surface can release wash water and debris. A suitable resin can avoid the repainting cycle associated with steel.
Those benefits do not make FRP the stronger material in every condition. FRP is generally less stiff than steel, and a demanding duty may require a deeper pultruded section, more molded depth, closer supports, a different frame or steel itself. Severe impact, high temperature, shallow structural depth and a structural fire-integrity requirement can favour another system.
The useful comparison is the complete duty:
- the same wheel, axle, equipment-foot or line loads;
- the same bearing seats and clear spans;
- the same deflection limit;
- the same chemical, temperature and fire requirements;
- the same fixing and installation scope;
- the same technical evidence and document standard.
Our FRP versus steel guide explains that comparison without treating corrosion resistance as a universal victory.
What the Main Heavy-Duty Grating Types Can Solve
Molded High-Load Grating
Molded grating is made as an integral grid. That connected geometry can distribute load in two directions and suits frames where supports run in more than one direction or the panel layout contains many changes and openings.
Heavy-duty molded directions commonly use greater depth or a different bar and mesh pattern than ordinary pedestrian panels. Our current range contains two deeper product rows to review:
- 50 mm: 25 × 50 mm mesh and 45.0 kg/m² reference mass.
- 63 mm: 38 × 38 mm mesh and 52.5 kg/m² reference mass.
These are current configurations, not declared heavy-duty ratings. The actual load, bearing edges, clear span, cut-out layout, deflection limit and evidence must match the finished panel. The molded grating product page lists the broader established range.
Pultruded Heavy-Duty Grating
Pultruded grating uses parallel I, T or WT bearing bars joined by cross rods. The principal load path follows the bars, and both ends of every load-bearing bar must reach support. The section, pitch and bearing direction belong to the structural definition.
Our currently published pultruded series covers bearing-bar heights from 25.4 mm to 50.8 mm. A project that needs a longer span may compare a deeper available section, a different support spacing or steel. The pultruded selection guide explains how to compare the actual profile.
A pultruded panel is not stronger merely because it is pultruded. A molded grid can be the better structural and fabrication candidate for a framed layout, while a pultruded bar can be inefficient if its bars do not follow the span.
Covered and Solid-Top Assemblies
A covered panel may be selected for a loading or storage area that needs a more continuous surface. The cover changes mass, drainage, joints and the structural basis of the assembly. A top cover does not automatically turn the base grating into a heavy-duty vehicle panel. The covered grating guide explains that boundary.
Load Cases That Define Heavy Duty
Uniform Load
Uniform load is distributed over an area and recorded in kPa or kN/m². It can describe a material layer, a broadly supported floor use or a design live load. State the loaded area, whether panel self-weight is included and the duration.
A uniform value does not answer what happens under an equipment foot or wheel. Dividing a machine’s total mass by the whole surrounding floor area hides the local action that may control the panel.
Equipment Feet and Point Loads
Equipment feet, pump bases, jacks, ladder feet and stored items deliver concentrated load. Record the individual force, contact footprint and position relative to bars, cross rods, joints and supports.
The word point load can be misleading because every real contact has an area. A small pad between bars can produce local bending and contact stress that a larger pad carrying the same total force does not.
Line Load
A rail, skid, wall base or machine support can deliver force along a length. Record the force per unit length, contact width, direction and whether the line crosses panel joints or unsupported edges.
Forklift and Vehicle Wheel Loads
A forklift or truck introduces moving wheel loads. Useful inputs include:
- unladen and laden vehicle mass;
- individual wheel or axle loads;
- tyre or caster contact dimensions;
- the route and position of each wheel;
- turning, braking and any dynamic or impact assumption;
- frequency of use and expected life;
- clear span, support location and panel joints.
A single vehicle mass is not enough. A forklift can impose a more demanding local action because the load is concentrated and moving. Turning near a panel edge or joint may create a different case from straight travel through the centre.
Impact
Dropped tools, equipment strikes and wheel impact are separate from a gradually applied static load. The review needs the object, energy, contact area, location and consequence of damage. Cracked bars, crushed edges, loose clips and damaged supports may require removal from service.
Repeated and Sustained Loads
A load that remains in place for months or years can cause creep. Elevated temperature can increase the effect. Repeated vehicle traffic can introduce dynamic and wear considerations not represented by one static test row. State duration, cycle count and normal or peak temperature where known.
The temperature and creep guide explains why short-term ambient data may not settle a permanent hot-service load.
What H20 and “Forklift Rated” Actually Require
Catalog and search results often repeat H20, vehicle load, forklift traffic and high load capacity. These phrases are not interchangeable universal product classes.
H20 and HS20
H20 and HS20 are vehicle-load references associated with certain highway and structural design contexts. If a project names H20, the enquiry should also establish:
- the governing edition or project standard;
- the design vehicle and axle or wheel arrangement;
- load placement and any multiple-presence rule;
- impact, dynamic or load-factor assumptions;
- deflection or serviceability limits;
- the exact cover, panel, frame and support assembly;
- the required calculation, test or approval route.
Without those inputs, “H20 grating” is a procurement slogan rather than a traceable specification.
Forklift Loads
“Forklift rated” should also prompt further questions: What forklift, at what load, on which wheels, over which route, across which supports and with what impact or cycle count? A pedestrian panel does not become a vehicle panel because it has greater depth or a grit surface.
Why These Labels Must Not Be Transferred
An H20 or heavy-duty label cannot move from one product, supplier or support condition to another. The finished product, support arrangement and acceptance criteria matter. Our quotation can identify whether the required evidence exists for the proposed configuration; it does not convert a customer label into an approval.
Recommended Load, Ultimate Capacity and Deflection
Load tables use different value types. Before applying any number, identify whether it is:
- an allowable or recommended working load;
- a design value with a stated load factor;
- a test load;
- an ultimate or observed failure load;
- a serviceability result at a stated deflection.
These are not equivalent. An ultimate capacity is not a working load, and a working load cannot be transferred to another panel configuration without the same evidence basis.
Deflection must be checked with strength. A panel can remain intact yet deflect enough to feel unstable, damage equipment, affect drainage or create movement at a joint. Deflection limits vary by application and project: common examples in published design guidance may be an absolute value, span/120, span/200 or another case-specific criterion. The governing project document and source still control.
For pultruded projects, use the pultruded span and deflection comparison to match the exact section, support condition, load pattern and deflection criterion before ranking candidate rows.
Static ambient tables may not cover impact, repeated traffic or long-term creep. A higher temperature or permanent load can require additional evidence. Do not invent a universal reduction factor or treat the absence of a table as zero effect.
Our Existing Factory Evidence
Our factory test report HZTC/BG-24051102 records a 4 kN/m² equivalent uniform design-load test over a stated 600 mm span, with material results including tensile strength and oxygen index.
The report does not identify one complete heavy-duty panel model, molded mesh or pultruded section, resin and finished support configuration. It is useful sample and material evidence. It is not an H20 approval, forklift rating or universal load table for every panel we make.
HZTC/BG-24051102 report
Can show: a recorded 4 kN/m² equivalent uniform design-load test at a stated 600 mm span, plus named material results.
Does not close: a complete panel model, every resin or surface, H20, forklift duty, dynamic traffic, permanent load or another support layout.
50 mm and 63 mm molded rows
Can show: current factory configurations with identified mesh and reference mass.
Does not close: a universal heavy-duty rating before the exact finished panel, supports, span, load and deflection are matched.
25.4–50.8 mm pultruded series
Can show: the published range of bearing-bar heights available for project review.
Does not close: one capacity for every I, T or WT section, pitch, bearing direction or support layout.
Approved panel drawing
Can show: the intended dimensions, bar direction, openings, edge treatment, piece marks and revision.
Does not close: a structural approval unless the load and support evidence for that drawing is also established.
A complete evidence pack therefore links the product data to the quotation and drawing. If a customer supplies a vehicle class or a competitor’s table, we first identify whether the product configuration, load placement, support condition and acceptance basis are the same. Where they are not, the missing comparison is stated rather than filled with a transferred rating.
Heavy Duty FRP Grating Applications
Loading Docks and Yard Drains
Loading areas may impose vehicle wheel loads, turning, braking and impact. The grating often forms a removable or fixed cover over a trench or drain. The support frame is part of the vehicle duty; a panel cannot be approved in isolation.
Overhead Doors and Trench Crossings
Plant traffic can cross a linear trench at a doorway or yard entrance. Clear width, frame bearing, panel joints and the wheel path all need to be on one drawing. This is a shared boundary with the trench-cover guide.
Equipment Platforms and Maintenance Floors
Pump feet, valves, motors and maintenance equipment can produce local loads. The platform may also include service openings and removable sections. See fiberglass platform grating for the complete platform review.
Storage and Production Areas
Stored materials, trolleys and assembly equipment can create sustained or moving loads. A load that never moves is different from an occasional pedestrian crossing.
Chemical, Wastewater and Marine Areas
These environments add resin, temperature, fire, UV and fixing requirements. A heavy structural panel with the wrong resin remains the wrong product. Review resin selection and the project-specific chemical data.
When Steel Is the Better Starting Point
FRP is not the automatic answer for every high load. Steel may be the more practical starting point where:
- impact is severe or repeated;
- temperature is high;
- the available structural depth is shallow;
- the duty requires non-combustible structural fire behaviour;
- a very stiff, welded structural arrangement is needed;
- severe mechanical damage would create unacceptable consequences.
Some hybrid or project-specific composite systems may also fit better than a catalog FRP panel. The useful comparison remains the same: actual supports, loads, deflection, fire, impact and maintenance. Corrosion resistance is a strong advantage in the right environment, not a reason to ignore the structural duty.
Openings, Joints and Supports
A heavy-duty panel can lose much of its advantage at an opening or joint. The drawing should show:
- the clear opening and every wheel or equipment route that passes it;
- which bars are removed;
- how the remaining edges are supported or framed;
- where panel joints fall relative to the wheel path;
- the support and fixing of removable pieces;
- the edge treatment and inspection access.
Clips hold the panel and can keep adjacent edges aligned. They do not create a support. A joint that occurs between wheel loads may move differently from a continuous panel, and a cut bearing bar interrupts the pultruded load path even if the edge is sealed.
Review the cutting and sealing guide and clip guide before approving the drawing.
Resin, Fire and Surface Are Separate
A high-load geometry does not establish chemical, fire or anti-slip performance. A demanding environment may require:
- a chemical-resistant resin grade;
- a specified fire and smoke result;
- a conductive or anti-static product;
- a grit or other walking surface;
- a UV-stable finish;
- compatible stainless or coated fixings.
Each requirement needs its own standard, test and product scope. The resin guide, surface guide, and fire-rating guide explain those separate checks.
Inspection and Condition Limits
Heavy-duty duty increases the importance of inspection. Check:
- cracked, broken or permanently deformed bars;
- crushed or exposed cut edges;
- whitening, delamination or chemical attack;
- loose, missing or corroded clips;
- panel movement at joints or supports;
- corrosion, deflection or damage in the support frame;
- wear or loss of the walking surface;
- debris blocking drainage or changing the load path;
- changes in traffic, equipment or stored load from the original duty;
- any opening added after installation.
A damaged heavy-duty panel should not be returned to vehicle service simply because the remaining bars still look connected. Review the damage and the original evidence.
When a Heavy-Duty FRP Grating Review Stops
We can review a configuration and fabrication scope. A technically responsible review stops when the inputs needed for structural acceptance are missing.
Typical examples include:
- a vehicle weight without wheel or axle load and contact area;
- no support drawing or clear-span definition;
- a request to match a competitor’s unstated H20 test;
- an opening that removes bars without a support detail;
- a permanent high-temperature load with no long-term evidence;
- a requirement for structural fire integrity or a named approval not supported by the exact product;
- a request for complete platform design while only the grating and clips are in the supply scope.
The stop is not a refusal to supply. It is the point where production assumptions would become an uninformed structural claim. Documenting the missing item is more useful than supplying a panel with an unexplained “heavy duty” label.
How to Compare Heavy-Duty Grating Quotations
Ask every supplier to provide the same comparison table:
| Quotation field | What the answer must identify |
|---|---|
| Product structure | Molded or pultruded; exact depth, bar section and pitch |
| Load basis | Uniform, point, wheel, axle, line or impact case with values and contact areas |
| Span definition | Clear span, support arrangement and bearing width |
| Deflection | Limit, load at which it applies and evidence source |
| Duration and impact | Static, moving, repeated or sustained; temperature and cycle assumptions |
| Resin and surface | Exact grade/requirement, surface and associated evidence |
| Fixings | Clip family, material, quantity and support scope |
| Fabrication | Finished sizes, openings, bar direction, edge treatment and piece marks |
| Documents | Drawing, calculation, test report, certificate and the configuration covered |
| Packing and freight | Protection, weight, destination and delivery term |
A low panel price is not a heavy-duty answer if it requires a different support frame, more clips, more maintenance or an unsupported structural assumption. Our cost guide explains the commercial layers, while the quality guide explains the document scope.
Selection sequence
How We Assess a Heavy-Duty FRP Grating Project
Work from traffic and load case through supports, evidence and the approved panel schedule.
Separate pedestrians, maintenance tools, pallet trucks, forklifts, road vehicles, dropped objects and stored materials.
Record wheel or axle loads, tyre or caster contact areas, routes, turning, braking and any dynamic or impact assumptions.
Show bearing seats, support spacing, supported edges, free edges, joints and available structural depth.
Overlay every service opening, cut, removable cover and panel edge on the load path and frame.
Review molded two-way and pultruded directional candidates against the same layout, load and deflection limit.
Add chemical, temperature, fire, UV, repeated traffic and sustained load conditions to the structural case.
Check that the data or calculation covers the same section, pitch, resin, support, span, load position and deflection basis.
Record the approved section, bearing direction, openings, edge treatment, clips, documents, piece marks and revision.
Claim boundaries
What Heavy Duty FRP Grating Does Not Prove
These are the shortcuts most likely to turn a heavy-duty claim into an unsupported approval.
- Thickness is not a heavy-duty class — Depth alone says nothing about bar geometry, pitch, bearing direction, support span, load contact or deflection.
- Vehicle mass is not a panel load — A forklift or truck must be resolved into actual wheel or axle actions, contact areas and movement or impact assumptions.
- H20 is not a universal product property — Where H20 or another vehicle model is named, confirm the governing edition, design vehicle, load placement, dynamic basis and acceptance method for the exact product and support system.
- Recommended load is not ultimate capacity — A failure value must not be used as a working load. A design or recommended load must state its safety basis and service conditions.
- Static ambient data is not the complete case — Moving, impacting, repeated and long-term loads can require additional factors, evidence or limitations. Elevated temperature can add creep.
- A support frame is part of the load path — Panel reactions must be carried by a suitable frame. Grating clips restrain the panel but do not create bearing or structural support.
- Openings interrupt structure — Cut bars, unsupported edges and removable sections need explicit support. Edge sealing protects the laminate but does not restore the removed load path.
- Heavy duty does not imply all other performance — Fire, smoke, chemical, static-control, slip and UV performance are separate requirements with their own product evidence.
RFQ inputs
What to Send for a Heavy Duty FRP Grating Quote
The most useful package combines traffic data, support geometry, load cases, exposure and finished-piece requirements.
- Application and traffic — Platform, loading dock, yard drain, trench cover, ramp, storage area, assembly line or route.
- Vehicle or equipment data — Individual wheel or axle load, tyre or caster contact, route, turning, braking, operating weight and loaded condition.
- Other load cases — Uniform load, equipment feet, line load, dropped-object impact, stored material and repeated traffic.
- Support drawing — Beam or frame layout, bearing seats, supported and free edges, clear spans and available depth.
- Deflection criterion — Project limit and basis, including the effect on comfort, equipment, drainage and joints.
- Panel and opening schedule — Finished sizes, quantity, bearing direction, joints, cuts, openings and removable pieces.
- Service conditions — Chemicals, concentration, temperature, wet or dry service, cleaning, UV and fire or smoke requirements.
- Fixings and supports — Clip family, fastener material, support material, movement and whether the panel must be removable.
- Required evidence — Load table, calculation, test, standard, drawing, inspection record or certificate and the exact product scope.
- Delivery — Edge treatment, piece marks, packing, quantity, destination and required date.
Quote scope
Heavy Duty FRP Grating Price and Evidence Scope
Heavy-load configurations are quoted from the actual section, support duty, fabrication and document requirement.
Configuration-specific engineering
Heavy-duty depth or bar-section alternatives are quoted from the actual configuration, support duty and evidence requirement rather than one square-metre rate.
Fabrication
Factory cutting, openings, edge sealing, piece marks and removable sections are quoted against the approved panel schedule.
Fixings and packing
Clip family, fastener material, protection and transport packing are included only where listed in the quotation.
Evidence and delivery
Drawings, inspection records, test or calculation scope and freight are stated separately so offers can be compared on the same basis.
A heavy-duty panel is not priced from “2 inch” or “H20” alone. The quotation follows the selected section or molded geometry, resin, surface, finished pieces, fixings, evidence and delivery. Current 50 mm and 63 mm molded high-load candidates are quoted by configuration; pultruded panels follow the I, T or WT section and project drawing.
Project review
Send the Load Cases and Supporting Frame
Start with the drawing and known wheel, point or impact data. We will identify the configuration and evidence that still have to be confirmed.
- A vehicle mass alone is not enough to check grating
- Send the support drawing, wheel data and service conditions where available
- We identify the evidence needed for the actual configuration instead of transferring a label
Heavy Duty FRP Grating Questions
What does heavy duty FRP grating mean?
Is thicker FRP grating always more heavy duty?
What is the difference between molded high-load and pultruded heavy-duty grating?
Can heavy duty FRP grating carry a forklift?
Does H20 mean the grating is approved for road vehicles?
What load data should I request?
Can a static load table cover repeated forklift traffic?
Does a taller pultruded bearing bar always work better?
Can a 50 mm or 63 mm molded panel be used for vehicle traffic?
What should I send for a heavy-duty quotation?
This content was prepared and reviewed by Dengtai Industry’s technical and production team using the project conditions, available product data and applicable documents. Limits that require design, testing or approval are identified in the content. Content last checked: