Fiberglass and FRP Grating Prices for Molded Panels

How Resin Choice Changes the FRP Grating Price

Different resin systems and formulations have different prices, even for panels with the same thickness, mesh and dimensions. The published schedule applies to the named economical isophthalic polyester + alumina filler formulation. A change in resin requires a quotation for that specific configuration.

For vinyl ester, epoxy or phenolic grating, request a project quote. Send the chemical medium, concentration and operating temperature where relevant, along with any fire/smoke or other performance requirements. We review these conditions with the panel structure, finish, quantity and fabrication before quoting.

When comparing suitable resin options, keep the panel geometry, surface, quantity and delivery scope consistent so you can identify the actual material-related price difference. Request a quote for your resin and application.

Calculate the Price per Panel or Square Foot

For fiberglass grating price and cost comparisons, keep the same configuration and supply scope when changing units. FRP and GRP are both used as names for glass-reinforced plastic grating; a different name or unit is not a different material grade.

For the 40 × 40 × 25 mm ordinary-environment tree-pit base in the schedule, a listed 1220 × 4040 mm panel has an area of 1.22 × 4.04 = 4.9288 m². At the published USD 7.5/m² EXW rate, its plain-panel amount is about USD 36.97, before cutting, treatments, clips, packing and freight. This is a calculation from the schedule, not an order quotation, a stock promise or a walkway load approval.

An area rate in USD/m² divided by approximately 10.764 gives USD/ft². For that same row, USD 7.5/m² is about USD 0.70/ft², with the same formulation and EXW exclusions. Use the original m² rate for the quotation calculation rather than multiplying a rounded display conversion.

The mesh dimensions are the schedule identifiers; confirm the actual pitch, clear opening and bar geometry on the drawing. Special-pattern rows cannot be selected reliably from thickness or an opening count alone. Mold-record masses are approximate configuration references, not substitutes for the ordered specification or matched load data.

Full Panels or Factory-Cut Pieces: Compare the Same Finished Job

Factory cutting is quoted on the delivered piece area, considering the exact sizes and the loss they create. The cut-piece area rate is normally higher than the corresponding plain-panel rate. Its value depends on the finished job: fewer on-site cuts may help, but a higher rate is not automatically offset by a smaller purchased area.

Ask two questions when comparing a “free cutting” offer with another quote: what material area is being charged, and which work is already included? Free straight cuts do not by themselves tell you whether the charge is for whole panels or finished pieces. Equally, a cut-piece rate that already allows for nesting loss should not have that same loss added a second time.

Worked Example: Full-Panel and Finished-Piece Areas

For a separate area-only teaching example, nine rectangular pieces of 400 × 1200 mm have a delivered area of 9 × 0.4 × 1.2 = 4.32 m². A 1220 × 3660 mm panel has a full area of 4.4652 m². An assumed 4 mm saw kerf allows three pieces across and three along in a rectangular layout. The difference of 0.1452 m² includes saw loss and remaining material; it is not a standard waste allowance.

Before using this layout, check the available mold size, edge trimming, complete bars, opening positions and supports. The 3660 mm teaching panel is not the 4040 mm panel used in the dollar calculation above, so its material rate must be confirmed separately.

Use actual quotations for the two rates. Confirm whether usable offcuts are supplied and who keeps them; do not automatically treat all remaining material as discarded. The lower total is the route with the better complete scope for your project. Prepare a cut list and review edge sealing.

From Ex-Works Price to Your Project Budget

The table prices the plain panel at the factory. Our usual export quotations are FOB, so compare the stated port and included costs before comparing totals. A factory price, an FOB order amount and a delivered-to-site budget are different figures.

FOB delivery is on board the vessel at the named loading port, with export clearance handled by the seller. The buyer normally arranges the main sea transport. If the actual handover is at a forwarder’s warehouse or a terminal instead, agree the appropriate term and responsibility split explicitly.

For a US or UK destination, send the country, city or port and the required arrival date. Import classification, applicable charges and transport arrangements need the actual shipment details; this page does not apply a universal duty, tax or freight percentage to the panel amount.

Small orders and bulk orders need different cost checks

We have no fixed minimum order quantity. For a few panels, packing, handling and transport may have more influence on the total than a small difference in the area rate. For a larger cut list, the size mix and nesting can matter as much as total square metres. Compare the delivered budget and timing before deciding whether a direct factory order fits the purchase.

There is no published automatic volume discount. Send the quantity and mix for a quote rather than treating 500 m² as a minimum or a discount trigger. Reducing the price by changing to a formulation that does not meet the duty is not a like-for-like saving.

Compare FRP and steel on the same duty

If you are also pricing steel, hold the required span, load, exposure and finished dimensions constant. Compare the panels and supports, fabrication, fixings, installation, transport, and the maintenance or replacement work the project actually expects. Without those inputs, neither a lower area rate nor a general “long life” claim proves the lower total cost. See the same-duty FRP and steel comparison.

Before accepting a quote, check its drawing revision, configuration, sizes and quantities, included work, currency, trade term, named port, payment, production schedule and validity. A price-table date tells you the reference used; only the quotation defines the offer for the order.