Industrial maintenance access

Fiberglass Catwalk Grating for Industrial Access

Use molded open mesh for short-span pedestrian access, or pultruded I/T bars where the support layout needs a directional structural solution. We make both in house and quote full panels, factory-cut pieces and agreed clips; steel supports, guardrails and structural approval stay separate unless included in writing.

Prepared by Dengtai Industry
Published · Reviewed

Molded and pultruded made in house Cut, seal, mark and pack Span and load reviewed together Panel and system scope separated
Yellow fiberglass grating catwalk with orange handrails above water-treatment basins

Elevated access over treatment basins. Photo: Dengtai Industry.

Definitions

What Is Fiberglass Catwalk Grating?

The panel is only the walking surface. The support layout, access requirement and project environment decide whether a molded or pultruded construction fits.

Fiberglass catwalk grating
An open fiberglass-reinforced plastic (FRP or GRP) walking surface used for industrial maintenance access. It can be molded or pultruded; the name describes the application and material family, not one fixed panel thickness or load rating.
Permanent maintenance access
An access route normally left in place for inspection, operation or service. Its width, access points, guarding, headroom and load requirements come from the project layout and applicable site requirements.
Catwalk and construction walkway
A catwalk normally serves a defined industrial maintenance route, often along equipment, pipework or the edge of a platform. A construction walkway can instead be a ground-level or temporary route. Similar panels may be used, but the design inputs and supply boundary are different.
Molded catwalk grating
A one-piece grid with intersecting bars. The molded panel can suit varied layouts, but the actual support spacing, bearing, loads, openings and deflection limit still need to be checked.
Pultruded catwalk grating
An assembly of parallel load-bearing profiles joined by cross rods. The bearing bars must run between the intended supports; rotating the panel changes the structural arrangement.
Clear span
The clear unsupported distance between the edges of adjacent supports. It is not the beam-centre distance and not the length of the purchased panel.
Bearing surface
The part of the frame or beam that actually contacts the grating. Correct beam spacing does not help if the panel rests only on a narrow edge, a weld high point or an unlevel surface.
Supply boundary
What is included in the order. Grating panels, cut pieces, openings and clips do not automatically include steel supports, guardrails, stairs, handrails, installation or structural calculations.

Fast suitability check

Is Fiberglass Catwalk Grating Suitable for Your Route?

Use these two lists to decide whether the project is ready for a grating review or needs a different scope first.

Specify this if…

  • The route is for pedestrians or carried maintenance tools, and the drawing identifies supports and clear spans.
  • Wet, corrosive, coastal or wash-down exposure makes a coated steel surface difficult to maintain.
  • Reduced panel weight matters for handling, lifting or an existing structure.
  • You need molded or pultruded panels, factory-cut pieces and clips, while supports or guarding are handled separately.
  • You can provide a layout now or mark the unknown engineering values for review.

Look elsewhere if…

  • You need a complete access system including structural design, steelwork, guardrails and installation under one scope.
  • Forklifts, heavy wheeled traffic, severe impact or high-temperature service govern and matching configuration evidence is not available.
  • A standard in-stock retail panel will meet the duty and an engineered factory order adds no value.
  • No one can establish the support arrangement, intended use or load requirement yet.

Product directions

Which Fiberglass Catwalk Grating Should You Start With?

Shortlist by the route and support condition. The final panel, resin and fixing still need to be confirmed against the project.

Yellow molded fiberglass grating with an integral square grid
Molded one-piece grid. Photo: Dengtai Industry.

30 mm molded open-mesh grating

Our usual pedestrian starting direction for ordinary access. Confirm the exact panel structure, support spacing, load and deflection before applying it to a catwalk.

Green molded fiberglass grating with a textured walking surface
The surface and panel depth are separate decisions. Photo: Dengtai Industry.

38 mm molded open-mesh grating

A deeper molded direction to compare when the verified span or duty calls for more structural depth. Thickness alone does not establish capacity.

Pultruded fiberglass grating with parallel bearing bars and cross rods
Pultruded bearing bars run in one principal direction. Photo: Dengtai Industry.

Pultruded I, T and WT grating

Directional bearing bars for layouts where the support run and structural section suit pultruded construction. Panels are made to project dimensions.

Factory-cut green fiberglass grating pieces with openings
Pieces can be cut and marked to the approved list. Photo: Dengtai Industry.

Factory-cut catwalk pieces

Cut sizes, pipe openings, edge sealing and piece marks can be coordinated on one cut list before production and packing.

Factory range

Fiberglass Catwalk Grating Sizes and Published Panel Prices

The table shows the molded configurations with a published panel base and the pultruded series made to order. Prices are plain-panel EXW references, not installed catwalk prices.

Swipe horizontally to view all columns.

ConstructionFactory configurationStandard panel or formatPublished panel baseFirst catwalk check
Molded 25 mm 38 × 38 mm mesh 1000 × 4000 mm; 1220 × 3660 mm USD 10.5/m² EXW Verify the exact span, load and deflection case
Molded 30 mm 38 × 38 mm mesh 1000 × 4000 mm; 1220 × 3660 mm USD 12.0/m² EXW Our usual ordinary-pedestrian starting point
Molded 38 mm 38 × 38 mm mesh 915 × 3050 mm; 1000 × 4000 mm; 1220 × 3660 mm USD 15.1/m² EXW Compare matching structural data at the project span
Molded 50 mm 50 × 50 mm mesh 1220 × 3660 mm; 1220 × 4000 mm USD 15.7/m² EXW Confirm whether the deeper panel is supported by project data
Pultruded I25, I38, T38, T50, WT38 Select the exact bearing-bar series and pitch Width × bearing-bar length; made to order Quoted by configuration Bearing direction, end support, span, load and deflection
Factory-cut pieces Molded or pultruded Drawing, cut list and piece marks Cutting scope quoted separately Openings, remaining bars, edge sealing and packing

Quick answer: for an ordinary pedestrian maintenance route with short, verified spans, start by reviewing 30 mm molded open-mesh grating. Compare a deeper molded section or pultruded I/T/WT grating when the support run, load or layout points that way. Use factory-cut pieces when the route has returns, pipe penetrations or several widths. The panel family is only the beginning; clear span, bearing, load, deflection, environment and supply boundary decide the specification.

If you are still comparing the material itself rather than a defined catwalk route, begin with the fiberglass grating overview.

Which Fiberglass Catwalk Grating Fits the Route?

Route conditionStarting directionWhat must be confirmed
Ordinary pedestrian access with short supported runs30 mm molded grating, 38 × 38 mm meshPanel structure, clear span, actual loading and deflection limit
The checked molded span needs more structural depth38 mm molded grating or a different molded structureApplicable load and deflection data, not thickness alone
Directional bearing is set by a long support runPultruded I, T or WT gratingBearing-bar direction, support at every bar end, section, span and load
Many widths, returns, pipes or inspection openingsMolded or pultruded factory-cut piecesCut list, opening positions, remaining support, edge treatment and piece marks

The wrong first question is “What is the strongest panel?” The useful first question is “What reaches the supports, and what condition controls the design?” A heavier panel on the wrong support layout is not a better answer.

How Much Load and Span Can Fiberglass Catwalk Grating Handle?

There is no single load rating for the material name or for a nominal thickness. Start with the actual panel structure, span definition, supported edges, load pattern and deflection limit.

For two 38 mm molded structures used in our range, we hold adopted reference data from a published Webforge load table. The values below show how a small change in bar pitch and span changes the result:

Source span6 × 38 mm bars at 38 mm pitch6 × 38 mm bars at 19 mm pitch
450 mm15 kPa, 1.0 mm deflection15 kPa, 1.0 mm deflection
600 mm15 kPa, 2.4 mm deflection15 kPa, 2.4 mm deflection
750 mm10 kPa, 3.7 mm deflection10 kPa, 3.6 mm deflection
900 mm5.0 kPa, 3.8 mm deflection7.5 kPa, 4.7 mm deflection
1200 mm2.5 kPa, 5.9 mm deflection2.5 kPa, 4.8 mm deflection

The figure is the additional uniformly distributed load U, excluding the grating’s own mass; D is the paired deflection. The source states a single-span basis and a safety factor of 5. It describes its dimension as span, so the definition still has to be matched to the project drawing.

At 1200 mm, the 38 mm pitch structure reaches a listed 5.9 mm deflection under 2.5 kPa. If the project limit is 5 mm, that row fails even though the table contains a load value. This is why we do not quote a “maximum span” from thickness alone. Read the complete load and span methodology before transferring a row to a catwalk.

The values are external reference benchmarks, not Dengtai test results for every product. Our own factory report HZTC/BG-24051102 separately records a 4 kN/m² equivalent uniform design load at a stated 600 mm test span for submitted samples, but its specification field does not identify every model, thickness, mesh and resin. Neither source can approve a project without matching the supplied configuration and conditions.

Why FRP and GRP Are Worth Comparing for a Catwalk

A suitable fiberglass catwalk panel can solve several practical problems at once:

  • Corrosion and wash-down: a matched resin system can avoid the rust-repair cycle of unprotected steel in wet, chemical, wastewater or coastal areas.
  • Handling: finished grating is generally lighter than a comparable metal access surface, which can help with removable panels, roof routes and structures with limited spare capacity.
  • Drainage and airflow: open mesh lets water, air and light pass through instead of forming a continuous floor.
  • Electrical and thermal behaviour: suitable FRP is non-conductive, although that does not replace the electrical assessment of the area.
  • Integrated fabrication: panels can be cut, opened and marked to a project layout, reducing field fitting where the drawing is reliable.

Those advantages are conditional. FRP has lower stiffness than steel, so deflection can control the support spacing before strength does. Fire, smoke, vehicle impact, sustained load, temperature and chemical exposure are separate checks. An ordinary polyester panel should not be presented as a universal substitute for every steel floor.

Five Decisions That Prevent Rework After the PO

Our first review focuses on the decisions that change the finished piece, not only the material family.

1. Clear Span and Bearing

Record beam-centre distance, clear span and bearing width separately. A load table is compared with a defined span and support condition; using the panel length or beam centres as the clear span can make the result look better or worse than reality.

A catwalk frame also has to offer a flat contact surface. A panel that rocks on a weld or sits on a narrow edge needs the support reviewed before clips are tightened. A shim used to hide a gap can create a hard point rather than solve the bearing.

2. Direction, Joints and Panel Splits

Pultruded bearing bars have to run from one effective support to another. The cross rods connect the assembly; they are not a second structural span. Molded grating does not have the same one-way bar system, but the intended top face, support contact and cut layout still matter.

When the catwalk route points toward pultruded construction, use the I, T and WT bar selection guide to turn the support direction, clear span and load case into a panel definition.

Panel joints must also land intentionally. A C clip can keep two edges level; it does not create a beam underneath the joint. If a joint sits between supports, the layout needs a support or a different panel split.

3. Openings and Removable Sections

Pipe openings, valve access and lift-out inspection pieces are not cosmetic cuts. The opening can remove molded bars or pultruded bearing bars, and the remaining strips need support. Mark the opening position, its distance from supports and whether the piece is permanent, removable or frequently handled.

For the full route split, see catwalk clear width and removable-panel layout.

Removable pieces require their own weight, lifting method and refitting detail. A correct panel geometry can still be unusable if one finished piece is too large or awkward to carry safely.

4. Environment, Resin and Surface

Define the environment by area. A dry covered walkway, a wash-down zone and a chemical dosing platform should not inherit one resin decision merely because they are in the same plant.

Vinyl ester is our usual direction where wastewater, chemical or marine exposure governs. Phenolic is considered where fire, smoke or structural fire criteria are stated. These are starting directions, not certificates. The grade, chemical concentration, temperature, exposure type and required evidence still need confirmation. The resin selection guide sets out those questions.

Concave grating is common where drainage and cleaning matter. Grit can be considered for wet or oily access, but it can trap debris. A claimed slip class must be tied to the test method and product tested.

5. Supply Boundary and Documents

A complete catwalk normally includes grating, clips, supports, guardrails, stairs, anchors, access design and installation. Our standard scope is the grating, agreed fabrication, clips and packing. Steelwork, guarding and installation remain outside unless they are separately quoted.

That boundary should be visible before the price comparison. It prevents a low panel rate from being compared with another offer that includes more fabrication, accessories, testing or delivery scope.

How Fiberglass Catwalk Grating Is Installed

Installation begins before the first panel is moved onto the frame:

  1. Check the delivered pieces. Reconcile piece marks, sizes, openings, finish and quantities with the packing list and current drawing revision. Record transit damage before installation.
  2. Measure the existing supports. Confirm beam positions, clear spans, bearing widths and level against the drawing. Resolve a rock or a high point before cutting or tightening the panels.
  3. Dry-lay the route. Confirm panel direction, intended top face, joint positions, opening locations and access to every fixing point.
  4. Cut and drill only from the approved layout. Support and control both sides of the work, use suitable composite cutting tools and protect the cut faces with the agreed compatible treatment.
  5. Fit M and L hold-downs. Match the clip to the panel height, bar and support. Tighten the panel without crushing the bars; a clip that must be forced is a fit problem.
  6. Fit C panel connectors where shown. Keep the walking surface level, but provide structural bearing under any joint that needs to carry load.
  7. Inspect before handover. Check rocking, joint steps, missing hardware, cracked bars, opening support, edge sealing and piece marks. Record deviations and the final drawing revision.

The detailed sequence is in our FRP grating installation guide, and the clip geometry is shown in the M, L and C fixing guide. The site installation method and the supporting structure remain the project’s responsibility unless separately agreed.

What We Do Differently as a Manufacturer

We make both molded and pultruded grating in house. That changes the starting point of the quotation: the comparison can follow the support layout and bearing direction rather than a sales preference for one structure.

For molded catwalks, the normal starting panel is supplied as a standard sheet or cut to a project piece list. For pultruded catwalks, panel width and bearing-bar length are made to order, and the cross-rod and piece layout are agreed with the drawing. We do not treat two pieces with equal outer dimensions as interchangeable if their bar direction or cutouts differ.

The most useful factory control is traceability from drawing to delivery:

  1. approve the layout and revision;
  2. freeze the finished-piece and opening list;
  3. manufacture the selected panel or bar assembly;
  4. cut and seal the included faces;
  5. check dimensions, appearance and piece identification;
  6. pack against the same list.

This is practical value that a generic benefits article cannot provide. It is also why we ask for the drawing before treating a square-metre rate as a meaningful comparison.

When Ordinary Fiberglass Grating Is Not the Best Answer

Stop and review the duty when:

  • forklifts, heavy wheeled plant or repeated impact govern;
  • high temperature, hydrocarbon fire or structural fire integrity is an acceptance criterion;
  • a complete support, guardrail and installation system is required with one design responsibility;
  • the chemical exposure has not been identified and no suitable compatibility evidence can be matched;
  • no support layout or intended use can be established.

These cases can still be discussed, but they need the correct evidence, product or wider system. An ordinary pedestrian panel should not be promoted into a vehicle floor, fire barrier or certified platform merely because it carries the FRP name.

What a Good Catwalk Grating Quote Contains

Send the layout, supports, dimensions, openings, quantity, destination, known loads and environment. The quotation should then make five things visible:

  • the proposed molded or pultruded construction;
  • what is supplied as panel, fabricated piece or clip;
  • the unresolved technical values and their effect on production;
  • what documents are available for the order;
  • what support, guarding or installation scope remains outside the offer.

That is the standard we use for this page. It is also the shortest route to comparing a factory quotation with a catalog price without mixing two different scopes.

Written and reviewed by the Dengtai Industry team using its published molded and pultruded grating configurations, factory photographs and installation guidance. Updated 21 October 2026. Project-specific supports, loads, guarding and approvals remain subject to the project documents.

Industrial applications

Where Industrial Catwalk Grating Is Used

Each route brings different loads, exposure and access requirements. Start with the operating condition rather than a generic panel thickness.

Orange pultruded grating floor around industrial pipework and process equipment
A grating floor around process equipment. Photo: Dengtai Industry.

Equipment and pipework access

Use the grating for a defined walking route around pumps, valves or process pipework. Before choosing a panel, mark the support beams, the clear spans, access openings and any point where tools or equipment will be placed.

Send the equipment layout, walking-route width, support plan and maintenance loads.

Yellow fiberglass grating walkway and handrails at a treatment facility
Treatment-plant access walkway. Photo: Dengtai Industry.

Wastewater and treatment plants

Wet, washed and chemically exposed catwalks need the resin, fixing material, surface and cleaning method considered with the process area. Vinyl ester is a common starting direction where corrosion governs, but suitability still depends on the actual medium and conditions.

State the chemical, concentration, temperature, contact type and cleaning regime.

Yellow fiberglass grating maintenance route between rows of solar panels
A maintenance route between solar arrays. Photo: Dengtai Industry.

Roof and solar maintenance routes

A narrow maintenance route can follow existing rails or track, but the support spacing, fixing connection, panel uplift, fall protection and access to the array all require review. A walkway photograph does not establish wind or structural performance.

Send the rail spacing, fixing positions, roof constraints and maintenance access plan.

Open grating access way with yellow railing beside a vessel and open water
A marine access reference. Photo: Dengtai Industry.

Marine and offshore maintenance access

Salt, hydrocarbons, fire requirements and long-term exposure can change the resin, fixings and documentation. The project needs to name which requirement governs each area instead of treating corrosion and fire as the same decision.

Provide the exposure, required fire or smoke criteria and document scope.

Factory-cut green fiberglass grating pieces with rectangular openings
Factory-cut pieces. Photo: Dengtai Industry.

Factory-cut routes with changes of direction

Long runs, returns, pipe penetrations and several panel widths are easier to reconcile before fabrication. A checked piece list reduces site cutting, but support around every opening and cut edge still has to be reviewed.

Send the dimensioned layout, opening positions, drawing revision and piece marks.

Panel structure

Molded or Pultruded FRP Catwalk Grating?

Compare the load path, panel direction, openings and support conditions on the same project layout.

Swipe horizontally to view all columns.

Selection pointMolded fiberglass catwalk gratingPultruded FRP catwalk grating
Load-bearing structure One-piece grid with bars formed together; the panel geometry and support layout determine how load is distributed. Parallel bearing bars carry the principal load; cross rods connect the assembly but do not create a second bearing direction.
Orientation Confirm the intended top face, joint pattern and support contact; molded construction still needs a layout check. Mark the bearing-bar direction. Both bar ends must reach the intended supports.
Typical starting point 30 mm, 38 × 38 mm molded grating is our usual starting point for ordinary pedestrian access, subject to the project check. I, T and WT pultruded series are selected against the support layout and required bearing-bar run.
Openings and changes of direction Cutouts interrupt part of the integral grid. Review the remaining strips and the support around the opening. A cut can remove bearing bars. The remaining bar ends and opening perimeter need their own support review.
Panel dimensions Standard molded panels include 1000 × 4000 mm and 1220 × 3660 mm, subject to the selected mold and finished piece list. Pultruded panels are made to project dimensions; width and bearing-bar length are confirmed on the drawing.
Main question to send Support plan, clear spans, bearing, accessible width, users and environmental exposure. Support plan, bearing direction, clear span and the required I, T or WT series.

Resin and treatment

Which Resin Fits the Catwalk Environment?

Start with the real medium and service condition. A resin family narrows the choice; it does not replace the grade-specific compatibility or fire evidence.

Swipe horizontally to view all columns.

Service conditionStarting resin directionWhat must be confirmed
Dry or ordinary outdoor access Isophthalic unsaturated polyester with alumina filler The exposure is genuinely outside strong chemical, permanent high-temperature and fire criteria
Wastewater, chemical or marine exposure Vinyl ester Medium, concentration, temperature, splash or immersion, cleaning and the grade-specific evidence
Fire, smoke or structural fire criteria Phenolic The exact standard, test method, acceptance limit, product tested and report required
Strongly corrosive project-specific duty Epoxy project review The exposure, proposed laminate, repair route and supporting evidence; resin name alone is not approval
Anti-static, UV or special finish Separate functional treatment Conductivity or earthing requirement, exposure, test method and required documents

Surface and fixings

Catwalk Grating Surfaces, Clips and Panel Joints

Surface, hold-down and panel connection are separate choices. Each has to match the walking condition, panel geometry and support.

Yellow molded fiberglass walkway grating laid on a steel support frame
Molded walkway grating in a supported industrial access condition. Photo: Dengtai Industry.

Concave walking surface

The standard molded walking surface. The bar profile forms a shallow channel that can help drainage and general underfoot traction; it is not a universal slip class.

Green molded fiberglass grating with a heavily textured grit surface
A textured grating surface. Photo: Dengtai Industry.

Grit walking surface

Consider grit for wet, oily or contaminated routes. It can improve traction but may retain debris, so surface and cleaning method must be selected together.

Metal M clip spanning two adjacent bars of yellow molded fiberglass grating
M clip fitted across two bars. Photo: Dengtai Industry.

M clip hold-down

The normal hold-down shape spans adjacent bars and bolts the panel to the support. The jaw, panel height, support section and access for tightening all have to match.

Metal C clip connecting edge bars on two adjacent fiberglass grating panels
C clip at a panel edge. Photo: Dengtai Industry.

C clip panel joint

A C clip keeps two panel edges level and controls the step at the joint. It does not create a support under the joint or increase the allowable span.

Project conditions

Catwalk Conditions That Change the Specification

From a new steel frame to an existing roof support, the information that changes the quote is usually outside the panel name.

Swipe horizontally to view all columns.

Catwalk conditionWhat to confirm firstWhat changes in the quotation
New-build steel frame Beam positions, clear spans, bearing width, level and fixing access from the structural drawing Panel type, direction, thickness or bar series, piece layout and fixing positions
Existing structure Measured support positions, condition and level of the existing steel, plus any obstruction Whether the existing frame can receive the required fixings and whether cut pieces are needed
Narrow maintenance route Access width, maintenance tasks, equipment carried, escape and guardrail requirements Panel split, edge restraint, fixing locations and the responsibilities outside grating supply
Wet or corrosive service Medium, concentration, temperature, splash or immersion, cleaning and fixing exposure Resin direction, surface, fixing grade and configuration-specific supporting documents
Pipes, valves or columns Exact opening locations, bars removed, distance from supports and remaining continuous bars Factory-cut opening, edge sealing, piece marking and possible support changes
Removable inspection section Finished-piece weight, lifting method, handling space, refitting and fixing arrangement Panel split and lifting provisions, coordinated with the selected clips and supports

Specification inputs

Fiberglass Catwalk Grating Specification Inputs

These are supply directions and configuration facts. Load capacity is confirmed from the selected panel, support layout, loading and deflection requirement.

Request a Project Quote
Specification Value
Usual molded pedestrian starting point 30 mm molded grating, 38 × 38 mm mesh A supply starting point for ordinary pedestrian access, not a load or span approval for a catwalk.
Manufacturing route Molded and pultruded grating made in house The factory can compare the two constructions against one project layout instead of treating one as the default.
Molded standard panels 1000 × 4000 mm; 1220 × 3660 mm Confirm the selected mold, thickness, finished dimensions and cut layout.
Pultruded build I25, I38, T38, T50 and WT38 directions Select the exact profile, pitch, resin and bearing-bar direction against the project information.
Panel dimensions Standard molded panels or custom pultruded pieces Factory-cut molded pieces and made-to-order pultruded panels can be included in the supply.
Resin direction Polyester, vinyl ester, phenolic or epoxy, as applicable Resin selection depends on chemical exposure, fire criteria, service conditions and available evidence.
Walking surface Concave or grit, with other options reviewed separately Surface and cleaning method are selected together; no universal slip class is claimed.
Fixing families M, L and C clips in galvanized or stainless steel Final clip type, material and positions follow the panel height, bar, support and exposure.
Fabrication Factory cutting, openings, piece marks and edge sealing when requested Sealing protects a cut edge but does not restore structural load paths removed by an opening.
Accessories Grating clips and agreed fixing components Steel supporting structure, guardrails, stairs and installation are not included unless stated in writing.
Evidence Order-specific documents available State the report, certificate, test method or approval required before quotation and production.

Before quotation

Project Information for an FRP Catwalk Quote

A useful inquiry connects the route, supports, loads, environment and supply scope on one drawing or clearly cross-referenced documents.

  • Catwalk layout — Plan and section showing the route, walking width, changes of direction, platforms, access points and the current drawing revision.
  • Support arrangement — Beam or frame positions, clear spans, bearing widths, level and the support that exists or is proposed.
  • Load and deflection — State the load type and value where known. Include equipment, carried tools, concentrated loads and the project deflection limit; unknown values can be marked for review.
  • Environment — Indoor or outdoor exposure, chemical or salt contact, temperature, wash-down method and fire, smoke or other acceptance criteria.
  • Panel direction and joint layout — Identify the bearing-bar direction for pultruded grating and the intended supports under every molded-panel joint.
  • Openings and maintenance access — Mark pipe, valve, column and inspection openings, and say whether any panel must be lifted or removed regularly.
  • Surface and fixing requirements — Describe wet, oily or dirty conditions, footwear, cleaning, fixing exposure and any required slip or other test evidence.
  • Supply scope and documents — State whether the quotation should cover panels, cut pieces, clips, edge sealing, packing, freight or any separately agreed accessories and documents.

Factory workflow

From Approved Catwalk Layout to Packed Grating

Our manufacturing sequence connects the panel configuration to the cut list, piece marks and documents that leave with the order.

01
Check the project fit

Review the intended access, existing or proposed supports, load information, environment and whether the request covers panels only or a wider system.

02
Choose the structure direction

Shortlist molded or pultruded grating from the support layout and load path, then identify the exact panel, resin, surface and fixing direction that still need confirmation.

03
Freeze the drawing and cut list

Confirm finished sizes, bearing direction, openings, edge treatment, piece marks, quantities, tolerances and the drawing revision before production.

04
Produce the grating

Manufacture the molded panel or assemble the pultruded bearing bars and cross rods to the agreed construction and dimensions.

05
Cut, drill and seal

Form the agreed openings and finished pieces, then treat the cut and drilled faces included in the order.

06
Inspect, mark and pack

Check the finished pieces against the approved list for appearance, dimensions, openings, edge treatment and identification, then pack for the transport route.

07
Issue the agreed documents

Provide the certificate of conformity, packing list or dimensional record agreed for the order, and identify any sample report by its actual product and test scope.

Price basis

Fiberglass Catwalk Grating Price and Supply Scope

Start with the published molded panel basis, then add the project-specific structure, resin, fabrication, fixings, packing and delivery scope.

Molded panel price starting point

The published plain molded base is USD 10.5/m² for 25 mm, USD 12.0/m² for 30 mm and USD 15.1/m² for 38 mm EXW. The listed basis is a 38 × 38 mm mesh in economical isophthalic polyester with alumina filler for ordinary environments.

What changes the delivered price

Pultruded sections, mini mesh, covered assemblies, vinyl ester or phenolic resin, nonstandard colors, cut pieces, openings, edge sealing, clips, piece marks, packing and freight are quoted against the actual scope. A panel rate is not a complete catwalk price.

Production and commercial basis

Our usual terms are 50% advance with the balance before dispatch. Normal production is typically 15–30 calendar days after deposit; transit is additional. We usually quote FOB, with the port and included costs named in the quotation.

Send the support drawing and layout you have. We return a configuration direction, the supplied scope, the open engineering values and any document limits in the same quotation, rather than presenting a panel price as a complete access-system approval.

Factory evidence

What Our Factory Controls and What the Project Still Owns

The strongest content is not a longer list of advantages. It is a traceable route from product configuration to the packed pieces, with the evidence limits stated.

Our factory workers finishing and checking yellow fiberglass grating panels
Panel finishing in our factory. Photo: Dengtai Industry.

Both structures are made in our factory

Molded and pultruded production are both in house, so the comparison can follow the support layout and required bearing direction instead of steering every project to one product family.

The cut list survives into packing

Piece marks tied to the installation layout can be carried through cutting and the packing list. For multi-piece routes, that makes the delivered parts easier to check and install in the intended order.

Review the factory quality and document route

The report is not stretched beyond its scope

Report HZTC/BG-24051102 records material and load results for submitted samples, including a 600 mm test span. It does not identify every panel model, resin and mesh, so it is not presented as a rating for every catwalk.

Read the original factory test report

The quote states the boundary

The quotation separates grating, fabrication and clips from steel support, guardrail, stair and installation responsibility unless another scope is expressly agreed.

Project inquiry

Request Fiberglass Catwalk Grating Pricing

Send the layout you have. The quotation can distinguish supplied grating and fabrication from values or structures that still need confirmation.

  • A clear review of the grating supply and what remains outside it
  • Molded and pultruded directions compared against the same project conditions
  • Attach a layout or sketch; unknown load and span values can be marked for confirmation
+ More specifications (size, quantity, span, environment)

PDF, DWG/DXF, image or Office file. If the file is larger than about 10 MB, email it to sales@frpgratingco.com instead.

Molded and pultruded grating · Full panels or cut to size · No fixed minimum order

Fiberglass Catwalk Grating Questions

What is fiberglass catwalk grating?

It is an open FRP or GRP grating panel used as the walking surface of an industrial maintenance catwalk. It may be molded or pultruded. The material family and generic product name do not establish the panel thickness, resin, support span or permitted load.

Is catwalk grating different from construction walkway grating?

The panel products can overlap, but the application differs. A construction walkway may be a ground-level or temporary access route. An industrial catwalk usually serves permanent equipment or maintenance access, so support, guarding, access width, load and documentation often become more specific.

Should I choose molded or pultruded FRP catwalk grating?

Choose from the support layout and load path. Molded grating is an integral grid that can suit varied layouts when its own span and support conditions are checked. Pultruded grating uses directional bearing bars that must run between supports. Neither construction is automatically better for every catwalk.

Can you supply the complete catwalk, including steel and handrails?

Our usual offer is grating, cut-to-size pieces, openings, agreed clips and packing. Steel supports, guardrails, stairs, installation and structural approval are outside that scope unless a written quotation expressly includes them.

What information do you need to quote catwalk grating?

Send the route layout, support or beam plan, clear spans, walking width, panel direction, openings, quantity, environment and destination. Add known load and deflection requirements. A sketch is enough to begin if some values are still unknown.

Can the panels be cut for pipe openings and changes of direction?

Yes. Send the opening positions and dimensions with the panel layout. We review how the cut affects the bars and support around it, include the factory cutting and edge sealing agreed for the order, and mark the finished pieces to the drawing.

What surface should I use for an outdoor catwalk?

Concave grating is common where drainage and cleaning are important. Grit can be considered where the route is wet, oily or contaminated, but grit may hold debris and needs a suitable cleaning method. A required slip class must be stated and checked against matching evidence.

What resin is suitable for a chemical or coastal catwalk?

The resin direction depends on the actual medium, concentration, temperature, contact type and documentation requirement. Vinyl ester is a common starting direction for corrosive or marine exposure, while phenolic is considered where fire, smoke or structural fire criteria govern. The final grade must be checked for the proposed configuration.

What is the load capacity of fiberglass catwalk grating?

There is no single capacity for all molded or pultruded catwalk panels. Capacity depends on the exact structure, bar dimensions and pitch, resin, support arrangement, clear span, load pattern and deflection limit. We can provide adopted reference data for matched molded structures and the factory sample report, but neither becomes a universal product rating.

How many clips does each catwalk grating panel need?

We do not publish one clips-per-panel number for every project. Fixing positions follow support lines, panel edges, joints, panel geometry, exposure and movement details. M and L clips restrain panels and C clips join edges; a clip does not create an additional bearing support.

How much does fiberglass catwalk grating cost?

The published plain molded panel base is USD 10.5/m² for 25 mm, USD 12.0/m² for 30 mm and USD 15.1/m² for 38 mm EXW in an ordinary-environment polyester configuration. Pultruded panels, other resins, covered assemblies, cutting, openings, sealing, clips, marking, packing and freight are quoted from the actual project scope.

Can fiberglass catwalk grating replace steel grating?

It can be considered on the same duty, but equal thickness does not establish equal stiffness or capacity. Compare clear span, load, deflection, fire or temperature criteria, impact, support, fixings and total project cost. Some heavy vehicle, high-temperature or severe impact duties remain better suited to steel.

This content was prepared and reviewed by Dengtai Industry’s technical and production team using the project conditions, available product data and applicable documents. Limits that require design, testing or approval are identified in the content. Content last checked:

Your choice is saved on this device. Cookie policy

Get Quote WhatsApp